Connect with us


Lg Dishwasher Troubleshooting Problems: Solve Your Dishwashing Woes Now!



Lg Dishwasher Troubleshooting Problems: Solve Your Dishwashing Woes Now!

To troubleshoot LG dishwasher problems, check that the waterline is properly connected and the water supply valve is open. Common issues include food particles blocking the filter or drain hose, a defective pump, a kinked drain hose, or a faulty motor.


An OE error code indicates a drain issue caused by food clogs or an obstruction. Other common problems with LG dishwashers include a door that won’t close, leaking, inability to drain properly, and unusual noises. To fix these issues, you may need to repair or replace the motor, hinges, or other components.


Lack of power, a broken door latch, a defective timer switch, and a blown thermal fuse can also cause the dishwasher to not start.


Leaking Water

Leaking water is a common problem that can occur with LG dishwashers. This issue not only leads to water wastage but can also cause damage to your floors or cabinets. It is essential to address this problem promptly to maintain the efficiency and longevity of your dishwasher. In this section, we will explore the causes of water leakage and provide you with steps to fix the issue.

Causes Of Water Leakage

Identifying the cause of water leakage is crucial in resolving the problem effectively. Here are some common causes to consider:

  1. Improperly connected waterline: Check to ensure that the waterline is properly connected to the dishwasher and that the water supply valve is open. A loose or disconnected waterline can result in water leakage.
  2. Blocked filter or drain hose: Food particles or debris can accumulate and block the filter or drain hose, causing water to leak from the dishwasher.
  3. Defective pump: A malfunctioning pump can lead to water leakage. Inspect the pump for any signs of damage or irregularities.
  4. Kinked drain hose: If the drain hose is bent or kinked, it can hinder proper water drainage and result in leakage. Make sure the drain hose is free from obstructions and positioned correctly.
  5. Faulty door seal: A worn or damaged door seal can allow water to escape during the dishwasher’s operation. Inspect the door seal for any signs of deterioration.

Steps To Fix A Leaking Dishwasher

Once you have identified the cause of water leakage, follow these steps to resolve the issue:

  1. Inspect the waterline and ensure it is securely connected to the dishwasher. Verify that the water supply valve is fully open.
  2. Clean the filter and drain hose to remove any blockages. Refer to the dishwasher’s manual for instructions on proper cleaning techniques.
  3. If the pump is found to be defective, consider replacing it. Contact LG customer support or a professional technician for assistance.
  4. Straighten any kinks in the drain hose and ensure it is properly positioned to allow smooth water flow.
  5. If the door seal is damaged, replace it with a new one. Ensure the seal is installed correctly to prevent future leakage.

Remember, if you are unsure about any of the steps or encounter difficulties during the troubleshooting process, it is always recommended to seek professional help. A qualified technician will have the necessary expertise to diagnose and fix the issue effectively. By promptly addressing and resolving water leakage problems in your LG dishwasher, you can ensure its optimal performance and longevity.

Not Draining Properly

Reasons For Poor Drainage

There can be several reasons why your LG dishwasher is not draining properly. Understanding these reasons will help you troubleshoot the issue efficiently:

  1. Clogged filter: Food particles and debris can accumulate in the filter, blocking the flow of water. To check if the filter is clogged, remove it and rinse it under running water.
  2. Kinked drain hose: The drain hose may become twisted or kinked, obstructing the water flow. Inspect the drain hose for any bends or obstructions and straighten it if necessary.
  3. Blocked drain hose: Over time, the drain hose can accumulate debris and become partially or fully blocked. To unclog it, disconnect the hose and use a long, flexible brush to remove any obstructions.
  4. Defective drain pump: If the filter and hose are clear, the issue might lie with a faulty drain pump. This can prevent the water from draining properly. In this case, you may need to replace the drain pump.

How To Unclog The Dishwasher Drain

If you’ve determined that the poor drainage is caused by a clogged dishwasher drain, here are the steps to unclog it:

  1. Turn off the dishwasher: Before starting any troubleshooting, make sure to turn off the dishwasher and unplug it from the power source.
  2. Access the drain: Locate the drain at the bottom of the dishwasher. It is usually covered by a grate or panel. Remove the panel carefully to access the drain area.
  3. Remove debris: Use a sponge or paper towel to remove any visible debris from the drain area. Be careful not to push the debris further into the drain.
  4. Use a vinegar and baking soda solution: Mix equal parts of vinegar and baking soda to create a bubbling solution. Pour it down the drain and let it sit for about 15 minutes. The fizzing action will help break down any remaining debris.
  5. Flush with hot water: After the solution has had time to work, flush the drain with hot water. This will help dislodge any loosened debris and clear the drain.
  6. Check the drain hose: While you’re unclogging the drain, also inspect the drain hose for any clogs or kinks. Straighten the hose if needed and remove any obstructions.
  7. Reassemble and test: Once you’ve cleared the drain and checked the hose, reassemble the dishwasher and plug it back in. Run a test cycle to check if the drainage issue has been resolved.
See Also  Maytag Bravos XL Dryer Troubleshooting Guide

By following these steps, you should be able to unclog the dishwasher drain and restore proper drainage.

Dishwasher Not Starting

If your LG dishwasher is not starting, it can be frustrating and inconvenient. However, there are several possible causes for this issue, and with some troubleshooting, you can get your dishwasher up and running again.

Possible causes for a dishwasher not starting

  • Lack of power
  • Broken door latch
  • Defective timer switch
  • Blown thermal fuse
  • Faulty motor starter relay or drive motor

When your dishwasher won’t start, it is essential to check for these common causes before proceeding with further troubleshooting steps.

Troubleshooting steps to get the dishwasher running

To resolve the issue of a dishwasher not starting, follow these steps:

  1. Check the power source and ensure that the dishwasher is properly connected to the power outlet.
  2. Inspect the door latch to ensure it is not broken or misaligned. If necessary, replace the latch.
  3. Examine the timer switch for any signs of damage or malfunction. A defective timer switch may prevent the dishwasher from starting. Replace it if needed.
  4. Inspect the thermal fuse, which is a safety device that can blow if the dishwasher overheats. If the fuse is blown, it needs to be replaced.
  5. If none of the above steps resolve the issue, it is recommended to check the motor starter relay and drive motor. These components may require professional assistance to diagnose and replace if necessary.

By following these troubleshooting steps, you can identify the cause of your LG dishwasher not starting and take appropriate action to get it back to proper working condition.

Noisy Operation

One of the most common problems experienced with LG dishwashers is noisy operation. A noisy dishwasher can be disruptive and annoying, especially if you have an open concept kitchen or if you run your dishwasher at night. However, there are several factors that can contribute to a noisy dishwasher and ways to reduce the noise. In this article, we will explore these factors and provide solutions to help you achieve a quieter dishwasher.

Factors Contributing To A Noisy Dishwasher

There can be several factors that contribute to a noisy dishwasher. Identifying these factors can help you determine the underlying issue and find a suitable solution.

  1. Worn Out Pump: A worn-out pump can be a common cause of excessive noise in a dishwasher. Over time, the pump can become clogged or worn out, leading to a noisy operation. Replacing or repairing the pump can help resolve this issue.
  2. Loose or Damaged Dish Rack: A loose or damaged dish rack can cause the dishes to vibrate and produce noise during the wash cycle. Make sure the dish rack is properly aligned and secure to minimize noise.
  3. Improper Loading: Improper loading of dishes can create imbalances and result in a noisy dishwasher. Ensure that the dishes are placed securely and evenly distributed to maintain balance and reduce noise.
  4. Water Supply Issues: Insufficient water supply or high water pressure can also contribute to a noisy dishwasher. Check if the water supply valve is fully open and the waterline is properly connected.
  5. Faulty Spray Arm: A faulty spray arm can cause excessive noise as it rotates during the wash cycle. Inspect the spray arm for any damages or blockages and replace if necessary.

How To Reduce Dishwasher Noise

Reducing dishwasher noise can enhance your overall kitchen experience. Here are some effective methods to help minimize the noise produced by your dishwasher:

  1. Place Soundproofing Material: Adding soundproofing material like adhesive foam or rubber pads to the sides and back of your dishwasher can help reduce noise by absorbing vibrations.
  2. Check for Leveling Issues: Ensure that your dishwasher is properly leveled to prevent excessive vibrations and noise. Adjust the leveling feet as required to achieve balance.
  3. Insulate Water Line: Insulating the water line using foam pipe insulation can help minimize noise caused by water flow. Wrap the insulation around the water line to reduce noise transmission.
  4. Inspect and Clean Filters: Routinely inspect and clean the filters in your dishwasher to prevent blockages. Food particles and debris can accumulate in the filters, leading to noisy operation.
  5. Use High-Quality Detergent: Using a high-quality dishwasher detergent specifically designed for quiet operation can help reduce noise. These detergents are formulated to create less foam and minimize noise during the wash cycle.

By implementing these solutions, you can significantly reduce the noise produced by your LG dishwasher and enjoy a more peaceful kitchen environment. Remember to always refer to the manufacturer’s manual or seek professional assistance if you’re unsure about any troubleshooting steps.

Poor Cleaning Performance

One of the most common issues that LG dishwasher users face is poor cleaning performance. If your dishes are not coming out clean after a wash cycle, there could be several possible reasons behind it. Identifying these reasons and implementing the necessary steps can help improve the cleaning performance of your LG dishwasher.

See Also  Mitsubishi Mini Split Not Blowing Cold Air: 10 Issues Fixed!

Possible Reasons For Dishes Not Being Cleaned Properly

Here are some possible reasons why your LG dishwasher may not be cleaning your dishes as effectively as it should:

  1. Blocked Filter or Drain Hose: Food particles can accumulate and block the filter or drain hose, preventing proper water flow and drainage.
  2. Defective Pump: A faulty pump may not be effectively spraying water onto the dishes, resulting in poor cleaning performance.
  3. Kinked Drain Hose: If the drain hose is kinked, it can restrict water flow and lead to inadequate cleaning.
  4. Faulty Spray Arms: If the spray arms are damaged or clogged, they may not distribute water evenly, resulting in uneven cleaning.
  5. Incorrect Loading: Improperly arranging dishes in the dishwasher can obstruct the spray arms and prevent proper water circulation.

Tips For Improving Cleaning Performance

To enhance the cleaning performance of your LG dishwasher, consider the following tips:

  • Pre-Rinse Dishes: Rinse off excess food particles from dishes before loading them into the dishwasher.
  • Clean Filter and Spray Arms: Regularly clean the filter and spray arms to ensure proper water flow and distribution.
  • Check Drain Hose: Ensure that the drain hose is not kinked or blocked, allowing smooth water drainage.
  • Use the Right Detergent: Use high-quality dishwasher detergent and follow the manufacturer’s instructions for optimal cleaning results.
  • Proper Loading: Arrange dishes properly, allowing adequate space for water circulation and ensuring that the spray arms are unobstructed.

By addressing these possible issues and following the tips mentioned above, you can significantly improve the cleaning performance of your LG dishwasher. Remember to consult your dishwasher’s user manual for specific guidelines and troubleshooting tips provided by LG.

Lg Dishwasher Troubleshooting Problems: Solve Your Dishwashing Woes Now!




Door Not Latching

Causes Of A Dishwasher Door Not Latching

If you’re facing the issue of a dishwasher door not latching, there could be several causes behind it. Understanding these causes will help you diagnose and fix the problem effectively. Here are a few common reasons why your LG dishwasher door may not be latching:

  1. Dirty or obstructed door latch: Over time, food particles, grease, or debris can accumulate around the door latch, preventing it from latching properly.
  2. Worn-out or damaged latch mechanism: Continuous use can cause wear and tear on the latch mechanism, leading to a faulty latch that fails to secure the door.
  3. Misaligned door: If the dishwasher door is misaligned, it may not align with the latch, resulting in a failure to latch.
  4. Broken door switch: The door switch is an essential component that signals the dishwasher to start when the door is closed. If the door switch is defective, it may prevent the door from latching.
  5. Loose or damaged door gasket: The door gasket forms a seal around the dishwasher door, ensuring that no water leaks out during the wash cycle. If the gasket is loose or damaged, it can interfere with the door’s ability to latch properly.

How To Fix A Faulty Latch

Fortunately, you can fix a faulty latch on your LG dishwasher without the need for professional assistance. Here is a step-by-step guide to help you resolve this issue:

  1. Clean the door latch: Start by cleaning the door latch using a soft brush, warm water, and mild soap. Remove any dirt, debris, or residue that may be obstructing the latch’s proper functioning.
  2. Inspect and replace the latch mechanism: If cleaning the latch doesn’t solve the problem, you may need to replace the latch mechanism. Refer to your LG dishwasher’s user manual for specific instructions on how to remove and replace the latch.
  3. Realign the dishwasher door: Check if the dishwasher door is misaligned. If so, you may need to adjust the door hinges to ensure proper alignment with the latch. Consult your user manual for guidance on how to adjust the hinges.
  4. Replace the door switch: If the door switch is faulty and preventing the latch from functioning correctly, it will need to be replaced. Refer to the user manual or contact LG customer support for guidance on replacing the door switch.
  5. Check and replace the door gasket: Examine the door gasket for any signs of damage or wear. If necessary, replace the gasket to ensure a tight seal and proper latching of the door.

By following these troubleshooting steps, you should be able to fix a faulty latch on your LG dishwasher, allowing it to latch securely and resume normal operation. Remember to always refer to your dishwasher’s user manual for specific instructions and safety precautions.

Display Error Codes

One of the convenient features of LG dishwashers is the display that provides information about the status and any issues with the appliance. When a problem occurs, the dishwasher will often display an error code to help you identify and troubleshoot the issue. Understanding the meaning of these error codes is essential for effective troubleshooting and resolving the problem.

Meaning Of Common Lg Dishwasher Error Codes

LG dishwashers commonly display error codes to indicate specific issues. Here are some of the most common error codes and their meanings:

Error Code Meaning
AE An AE error code typically indicates a problem with the dishwasher’s water supply. It could be due to a clogged filter, a kinked hose, or a faulty water inlet valve.
LE An LE error code suggests a motor-related issue. This could be caused by a faulty motor or a problem with the wiring.
OE An OE error code signifies a drain problem. It usually occurs when there is a blockage in the drain hose or when food particles clog the dishwasher’s drain system.
nE An nE error code indicates a problem with the dishwasher’s vent fan motor. This could be due to a faulty motor or a blockage in the vent system.
See Also  Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins

Steps To Resolve Error Codes

If you encounter an error code on your LG dishwasher, follow these steps to troubleshoot and resolve the issue:

  1. Refer to the dishwasher’s user manual for specific instructions on troubleshooting the error code.
  2. Check for any visible issues, such as clogged filters, kinked hoses, or loose connections. Address any identified problems.
  3. Power off the dishwasher by unplugging it or turning off the circuit breaker. Leave it off for a few minutes and then power it back on.
  4. If the error code persists, try running a cycle with no dishes to see if the issue is resolved. If not, you may need to contact an authorized service technician for further assistance.

Remember to always prioritize your safety when troubleshooting and, if necessary, consult a professional to avoid any risks.

Understanding the meaning of common LG dishwasher error codes and following the appropriate steps to resolve them can help you quickly get your dishwasher back to proper working order.

Foul Odor

Nothing can be more off-putting than a foul odor coming from your dishwasher. Not only does it make your dishes smell unpleasant, but it also raises concerns about cleanliness and hygiene. Thankfully, there are various causes of dishwasher odor, and with a few simple methods, you can eliminate the smell and restore freshness to your dishwasher.

Causes Of A Smelly Dishwasher

Understanding the root cause of the foul odor in your LG dishwasher is the first step towards resolving the problem. Here are some common causes:

  1. Food debris: One of the primary causes of a smelly dishwasher is food particles that get stuck in the filter or drain hose. These particles can decompose over time, resulting in a foul odor.
  2. Standing water: If water remains stagnant in the dishwasher, it can begin to smell. This may be caused by a faulty pump or a kinked drain hose.
  3. Mold and mildew: Moisture in your dishwasher can create a favorable environment for mold and mildew growth. These fungi can produce a musty odor.

Methods To Eliminate Dishwasher Odor

To eliminate the foul odor from your LG dishwasher, try these effective methods:

  1. Clean the filter and drain hose: Remove the filter and drain hose, ensuring there are no food particles or debris trapped inside. Use a soft brush or cloth to clean them thoroughly.
  2. Run a vinegar cycle: Fill a dishwasher-safe cup with white vinegar and place it on the top rack of the empty dishwasher. Run a hot water cycle to help break down any remaining food particles and eliminate odor.
  3. Use a dishwasher cleaner: There are several commercial dishwasher cleaners available that can effectively remove odor-causing residue. Follow the instructions on the cleaner to ensure proper usage.
  4. Prevent moisture buildup: Leave the dishwasher door slightly ajar after each use to allow air circulation and reduce moisture. Also, wipe down the interior regularly to prevent mold and mildew growth.
  5. Check for clogs: Ensure that the drain hose is not clogged or kinked. Clear any obstructions to promote proper drainage and prevent odor buildup.

By addressing the root causes of dishwasher odor and implementing these methods, you can restore a fresh and pleasant environment in your LG dishwasher. Say goodbye to foul odors and enjoy clean, odor-free dishes with these troubleshooting techniques.

Frequently Asked Questions For Lg Dishwasher Troubleshooting Problems


What Is The Most Common Problem With Lg Dishwashers?


The most common problem with LG dishwashers is a drain issue, often caused by food clogs or a faulty pump. Other common issues include a door that won’t close, leaks, a faulty motor, and improper drainage. To fix these problems, check the waterline and supply valve, clean the filter and drain hose, or contact LG support.


How Do I Clear The Error On My Lg Dishwasher?


To clear the error on your LG dishwasher, check if the waterline is connected properly and the water supply valve is open. Common causes for the error include food particles blocking the filter or drain hose, a defective pump, a kinked drain hose, or a faulty motor.


How Do You Diagnose A Dishwasher Problem?


To diagnose a dishwasher problem: 1. Check waterline and supply valve for proper connection and open valve. 2. Common issues include food particles blocking the filter or drain hose, a defective pump, kinked drain hose, or a faulty motor. 3.


An OE error code indicates a drain issue due to food clogs or an obstruction. 4. Most common LG dishwasher problems are related to drainage and constant error codes. 5. Troubleshoot by checking for lack of power, broken door latch, defective timer switch, blown thermal fuse, or motor issues.


What Is The Most Common Reason A Dishwasher Stops Working?


The most common reason a dishwasher stops working is due to a lack of power, broken door latch, defective timer switch, blown thermal fuse, or issues with the motor starter relay or drive motor. Make sure to check these components when troubleshooting your dishwasher.




In order to troubleshoot LG dishwasher problems, it is important to check common issues such as drainage problems, error codes, and faulty parts. Make sure to inspect the waterline and water supply valve to ensure proper connection. Food particles blocking the filter or drain hose, a defective pump, or a kinked drain hose are often the culprits.


Resolving unusual noises and a door that won’t close are also common problems. Seeking professional advice or using the LG dishwasher manual can help in identifying and fixing these issues. Remember, thorough troubleshooting is key to getting your dishwasher back up and running efficiently.

Continue Reading
Click to comment

Leave a Reply

Your email address will not be published. Required fields are marked *

mini split

Mitsubishi Mini Split Not Blowing Cold Air: 10 Issues Fixed!



Mitsubishi Mini Split Not Blowing Cold Air

The scorching summer heat is here, and there’s nothing worse than realizing your Mitsubishi mini split air conditioner isn’t blowing cold air. Instead of enjoying cool comfort, you’re left sweltering in a hot home.

Before you call in the pros, try troubleshooting the issue yourself. In most cases, a DIYer can get their Mitsubishi unit cooling again with minimal effort. This comprehensive guide will walk you through the top 10 reasons a mini split fails to blow cold air and how to fix each problem.

Common Causes of a Non-Cooling Mini Split

Several issues can disrupt the cooling capabilities of your Mitsubishi mini split system. Here are the most common culprits when the AC stops blowing cold air:

  • Clogged Air Filter: Restricted airflow from a dirty filter prevents proper cooling.
  • Wrong Mode: If the unit is switched to “Heat” instead of “Cool”, it will blow warm air.
  • Frozen/Dirty Coils: Blocked airflow due to icy or dirty evaporator and condenser coils.
  • Power Disruption: A tripped breaker or blown fuse interrupts power to the AC.
  • Unmaintained Unit: Dust and debris in the outdoor unit components reduce performance.
  • Refrigerant Leak: Low refrigerant levels due to a leak prevent the AC from cooling properly.
  • Clogged Drain Line: Condensation can’t drain leading to operational issues.
  • Faulty Compressor: Worn out or damaged compressor fails to circulate refrigerant.
  • Defective Thermistor: Disrupts the cooling signal to the AC.
  • Broken Fan Motor: Motor failure leads to lack of airflow.

By methodically troubleshooting each issue, you can get your Mitsubishi mini split blowing crisp, cold air again in no time.

Steps to Troubleshoot a Non-Cooling Mini Split

When your mini split stops blowing cold air, don’t panic. Just follow this systematic troubleshooting guide to identify and fix the issue:

1. Check the Air Filter

The first thing to check is the indoor air filter. A clogged, dirty air filter is the most common reason an AC fails to properly cool.

Over time, dust, pet hair, and other debris builds up on the filter screen. This clogs the filter and restricts airflow over the indoor unit’s evaporator coil. Less air circulation means less efficient cooling.

How to Fix:

  • Turn off and unplug the mini split.
  • Remove the front panel from the indoor unit to access the air filter.
  • Slide out the filter and inspect it. If it’s excessively dirty, clogged, or coated in debris, it needs to be cleaned.
  • You can vacuum the filter to remove loose dirt and dust. For heavier grime, wash the filter in warm soapy water. Rinse it thoroughly.
  • Allow the filter to air dry completely before reinstalling it. Never put a wet filter back into the unit.
  • Replace the clean filter, replace the front panel, and turn the mini split back on.

Be sure to check and clean the air filter every 3-6 months. Filters should be replaced at least once a year. Proper maintenance keeps airflow unrestricted for better cooling.

2. Verify the Temperature Mode

Another simple issue is having the wrong temperature mode activated on your mini split remote control or panel.

For cooling, the unit needs to be set to “Cool” mode. If it’s mistakenly switched to “Heat” mode, the system will blow warm air instead of cold.

How to Fix:

  • Check your remote control or indoor unit panel to verify which mode is currently selected.
  • Switch the mode to either “Cool” or “Auto”.
  • “Auto” mode will automatically adjust between heating and cooling as needed to maintain the set temperature.
  • The “Dry” mode on some units also activates cooling.
See Also  Mitsubishi Mini Split Not Blowing Cold Air: 10 Issues Fixed!

This allows the mini split to start lowering the room temperature and blow cold air as needed. Make sure it’s not stuck on heating mode when trying to beat the summer swelter.

3. Inspect the Coils for Frost or Dirt Buildup

The evaporator and condenser coils are vital components that can get blocked in various ways, preventing proper airflow and cooling distribution.

First, check for frost or ice buildup on the evaporator coil inside the indoor unit. In very hot and humid conditions, the evaporator coil can freeze over which blocks air from passing over it. Without airflow, the refrigerant won’t absorb heat and cool the air.

Next, inspect the condenser coil in the outdoor unit. Over time, dirt, dust, leaves, and other debris can stick to the coil fins blocking airflow. A filthy condenser coil prevents hot air from circulating and heat from dissipating properly.

How to Fix:

For frozen evaporator coils:

  • Set the mini split to run the fan at high speed. This will help thaw out the ice buildup.
  • You can also try carefully removing any ice with your hands if it’s accessible.
  • Once thawed, be sure to keep the filter clean and airflow unobstructed to prevent it from freezing again.

For dirty condenser coils:

  • Turn off the power to the outdoor unit.
  • Remove debris like leaves and dirt from the coil fins using a soft brush.
  • Rinse gently with a garden hose if needed.
  • Be careful not to damage the thin, aluminum coil fins which can affect performance.
  • Straighten any bent fins using a fin comb tool.
  • Clear away grass, weeds, or shrubbery right near the condenser. Allow at least 12 inches of clearance.

Keeping both the evaporator and condenser coils clean allows proper airflow for the mini split to cool efficiently.

4. Check for Power Disruptions

When troubleshooting why your mini split won’t blow cold air, you also need to look for any power supply issues. Loss of electrical power will shut down the entire AC system.

Check your main electrical panel for any tripped circuit breakers or blown fuses related to the mini split circuit. A tripped breaker or blown fuse cuts power to the unit. Power disruptions like a grid outage will also cut power.

How to Fix:

  • Locate the circuit breaker for the mini split and ensure it’s switched to the “On” position.
  • If it’s tripped to “Off”, flip the switch to reset the breaker.
  • Check fuses using a multimeter to see it they are still functional. Replace any blown fuse with a new one of the same amperage.
  • For suspected electrical issues, it’s best to contact a licensed electrician.

Restoring steady electrical power to your mini split will allow it to turn on and resume cooling your space.

5. Clean the Outdoor Unit

For optimal operation and cooling capacity, the outdoor unit of your mini split needs periodic maintenance. The outdoor unit contains vital components like the compressor, condenser coil, and a fan motor.

Over time, dust, dirt, leaves, grass clippings, and other debris can accumulate inside the outdoor unit housing. Excessive buildup on these components blocks proper airflow which reduces cooling performance.

How to Fix:

  • Turn off power to the outdoor unit at the breaker and disconnect any electrical connections.
  • Remove the top cover panel so you can access inside the unit.
  • Use a soft brush and vacuum cleaner to gently remove dust and debris from the condenser, fan blades, and other components.
  • Take care not to bend, damage, or disturb any refrigerant lines or electrical parts.
  • Use a damp cloth to wipe dirt from the compressor body. Avoid getting any components dripping wet.
  • Replace the cover when finished and restore power.

Routine cleaning keeps the condenser, fan, and compressor operating at peak efficiency for better cooling.

6. Address Refrigerant Leaks

The refrigerant circulating through the mini split system is vital for heat absorption and cooling. If there is a leak, the reduced refrigerant level can greatly affect performance.

Signs of a refrigerant leak include:

  • Damp spots around fittings, valves or coils in the outdoor unit. The evaporating refrigerant leaves oil residue.
  • Unusual odors around the unit like a sweet, chemical smell.
  • Higher utility bills from added run times due to reduced cooling capacity.
  • The system may still run but never quite reaches the set temperature.
See Also  Maytag Bravos XL Dryer Troubleshooting Guide

How to Fix:

If you suspect a refrigerant leak, immediately contact an experienced, licensed HVAC technician. Refrigerant systems are complicated and specialized tools/skills are required to properly diagnose, repair, evacuate, recharge, and test for leaks.

Trying DIY repairs often makes the problem worse and releases refrigerant which is harmful to the environment. The EPA requires proper refrigerant handling certification.

The technician will use leak detection dye and an electronic sensor to pinpoint the source of the leak. Then they can seal it, recharge the system with new R410A refrigerant, and get your mini split blowing cold air again.

7. Unclog the Drain Line

Room air conditioning units like mini splits remove humidity from the air during cooling. This condensation needs to drain away properly.

The indoor unit has a drain tube or pan that empties excess moisture outside. Over time, algae, slime, dirt, and debris can clog the drain line. When clogged, condensation builds up inside the unit rather than draining away. This water overflow can disrupt normal operation.

Signs of a clogged drain line include:

  • Water dripping from the indoor unit into your home.
  • Excess moisture visible inside the unit.
  • Reduced cooling and musty odors from excess humidity buildup.

How to Fix:

The best solution is to have an HVAC technician inspect, clean, and unclog the drain line completely. They can also treat the line to prevent future algae growth and clogging issues.

For DIY cleaning:

  • Shut off and unplug the mini split.
  • Locate the drain line port on the indoor unit (usually a rubber grommet).
  • Disconnect the drain line and examine it for obstructions like sludge, algae, dirt.
  • Clean out debris with a wet/dry vacuum suction tool.
  • Flush with hot water, vinegar, or drain cleaner.
  • Rinse thoroughly since chemicals can corrode the coil if any residue remains.
  • Reconnect the cleared drain line.

Keeping the drain line clear prevents excess humidity and allows proper water drainage for optimal cooling.

8. Check the Compressor

The compressor in the outdoor unit is the heart of the mini split system. This component circulates refrigerant through the indoor and outdoor coils to provide cooling. If the compressor is worn out or defective, the system loses its ability to cool properly.

Signs of compressor failure include:

  • Unit runs but doesn’t blow cold air.
  • Unusual noises from the outdoor unit like screeching, grinding.
  • Outdoor unit cycles on and off frequently.
  • Frost or ice buildup on the refrigerant lines.
  • High utility bills from increased runtime.

How to Fix:

If you suspect compressor failure, call an HVAC technician immediately. Diagnosing issues accurately requires specialized tools and expertise.

The technician will check for:

  • Bad start capacitors – Needed to start the compressor motor.
  • Burned out motor windings.
  • Damaged valves or bearings.
  • Leaks, cracks or broken fittings.

Repairing a compressor may be possible, but a technician is the best option to evaluate the extent of the damage. In many cases, total compressor replacement is needed.

Trying to recharge refrigerant in a unit with a bad compressor will likely worsen any leaks. Paying an expert to properly inspect and fix or replace a faulty compressor will get your system running optimally again.

9. Inspect the Thermistor

The thermistor (also called a thermal sensor) is a component that measures temperature changes in the refrigerant flowing through the system. It sends signals to the circuit board to adjust cooling output accordingly.

If the thermistor in the outdoor unit fails, it disrupts this vital communication between temperature measurements and cooling needs. The system won’t know to increase cooling when it gets hotter.

Signs of a faulty thermistor:

  • Erratic cooling – Unit frequently switches between warm and cold.
  • Icing up of the evaporator coil due to lack of temperature monitoring.
  • Temperature swings – Thermostat setpoint and actual room temp don’t match.

How to Fix:

Thermistors are delicate and complex. Diagnosing and replacing a bad outdoor unit thermistor should be done by a trained HVAC technician.

See Also  Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins

They will use a multimeter to check thermistor resistance and determine if it is still within the correct ohm range. If faulty, the thermistor will need to be replaced with a new OEM part.

Proper thermistor operation is crucial for monitoring system temperatures and maintaining ideal cooling.

10. Replace Broken Fan Motor

The outdoor unit contains a fan motor that blows air over the hot condenser coil to dissipate heat. If this condenser fan motor burns out, airflow will be reduced through the outdoor unit hampering its ability to cool.

Signs of a broken motor:

  • Loud grinding, buzzing noises.
  • Fan spins slowly or not at all.
  • Outdoor unit has to work harder causing the compressor to overheat and shut down.

How to Fix:

Replacing a burned-out condenser fan motor requires an exact OEM part number match and specialized skills to remove, rewire, and reinstall.

Contact a Mitsubishi authorized HVAC technician. Only a Mitsubishi OEM replacement motor will have the correct specs for your unit. Attempting to install a generic motor may hinder performance and cooling capacity.

When to Call an HVAC Technician

While many mini split problems can be DIY repaired, more complex issues require a professional. Contact a qualified HVAC technician for:

  • Refrigerant leaks – Recharging and finding leaks requires EPA 608 certification. Improper handling releases harmful refrigerants.
  • Drain line clogs – Severe obstructions in drain pipes may need professional rodding, jetting, or chemical treatments.
  • Compressor failure – Only a technician has the tools to accurately diagnose compressor issues. Compressor repair or replacement is specialized work.
  • Thermistor problems – Faulty thermistors need an expert diagnosis. Replacing them means handling refrigerant lines.
  • Condenser fan motor – Exact OEM replacement parts and proper installation is crucial.
  • Any major disassembly of sealed refrigerant components. Tampering voids warranties and releases refrigerants.

While some home DIY repairs are possible, mini splits are complex appliances. At the first sign of any refrigerant or sealed system-related problems, engage a certified HVAC company to get your unit running right.

Maintain Your Mini Split

Preventative maintenance is key to avoiding many mini split problems in the first place. Follow this schedule:


  • Check and clean air filters if needed. Replace every 3-6 months.
  • Clear away debris and vegetation around outdoor unit.

Every 3 months:

  • Clean dirt from outdoor unit coils with gentle water rinse.
  • Check for obstructions in air intake and outlet vents.


  • Replace air filters before summer and winter seasons.
  • Have an HVAC technician do a seasonal maintenance check-up and inspect refrigerant charge.

As Needed:

  • Clean fins on outdoor coils if they get bent or dirty.
  • Have drain lines professionally cleaned if you notice water leakage.

Enjoy Reliable Cooling from Your Mini Split

Mitsubishi makes incredibly efficient and reliable mini split air conditioners. But like any appliance, they can occasionally have hiccups.

If your unit starts blowing warm air instead of crisp, cold air, don’t panic. In most cases, the problem is minor and easily fixed with some DIY troubleshooting.

This guide walked through the top 10 most common issues that cause a mini split to stop cooling properly. By identifying the specific problem and methodically trying repairs, you can get your unit running optimally again.

Knowing when to DIY and when to call in an HVAC professional prevents further damage or safety risks. With proper maintenance and care, a quality Mitsubishi mini split system should provide many years of energy-efficient cooling comfort.

Beat the summer swelter by keeping your Mitsubishi mini split operating at peak performance. Refer back to these troubleshooting tips anytime your AC needs a quick pick-me-up!


A non-cooling Mitsubishi mini split can be frustrating, especially during hot weather. But in most cases, the issues can be quickly identified and repaired with some basic troubleshooting.

  • Start by checking for simple problems like a dirty filter, incorrect mode, or power supply interruption.
  • Inspect components like the coils, outdoor unit, drain line, and fan motor for common maintenance issues.
  • For more complex problems involving refrigerant, the compressor, thermistor or major repairs, engage a trained HVAC technician for safe diagnosis and servicing.

Preventative maintenance goes a long way in keeping your mini split running optimally year-round. But even well-maintained units can sometimes malfunction.

Now you’re equipped with the troubleshooting knowledge to get your Mitsubishi mini split blowing crisp, cold air in no time. Keep this guide handy for when your system needs a tune-up.

With just a few DIY repairs, you can stay cool and comfortable thanks to a properly operating mini split AC even on the hottest days!

Continue Reading


Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins



Where Are Kitchenaid Refrigerators Made

Kitchenaid refrigerators are primarily made in the United States, with manufacturing facilities located in states such as Ohio, Texas, and Tennessee. They take pride in producing a significant portion of their appliances in their home country.

Kitchenaid’s Manufacturing Locations In The United States

Kitchenaid’s Manufacturing Facilities In Ohio

One of the key manufacturing locations for KitchenAid refrigerators in the United States is Ohio. KitchenAid takes pride in producing a significant portion of its appliances in its home state. In fact, their dishwashers are all manufactured in Findlay, Ohio. This facility in Findlay is a massive manufacturing hub, playing a crucial role in KitchenAid’s production process.

Manufacturing Of Kitchenaid Appliances In Texas

In addition to Ohio, KitchenAid also has manufacturing facilities in Texas where some of their appliances are produced. While specific details about the types of appliances made in Texas are not readily available, it is clear that KitchenAid has a strong presence in the state, contributing to the production and distribution of their high-quality products.

Kitchenaid’s Manufacturing Facilities In Tennessee

Tennessee is yet another state with KitchenAid manufacturing facilities. Though specific information on which appliances are manufactured in this state is not easily accessible, it is evident that KitchenAid has established a solid manufacturing base in Tennessee. The presence of these facilities further strengthens KitchenAid’s commitment to producing appliances in the United States.

See Also  Maytag Bravos XL Dryer Troubleshooting Guide

Kitchenaid Refrigerators Made In Amana, Iowa

Built-in Kitchenaid Refrigerators Manufactured In Amana, Iowa

When it comes to KitchenAid refrigerators, one of the manufacturing locations that stands out is Amana, Iowa. KitchenAid takes great pride in producing a significant portion of its appliances in the United States, and their built-in refrigerators are no exception.

At their state-of-the-art facility in Amana, Iowa, KitchenAid manufactures high-quality built-in refrigerators that are designed to meet the needs of even the most discerning homeowners. These refrigerators are built with craftsmanship and attention to detail, ensuring both functionality and style.

By choosing a built-in KitchenAid refrigerator manufactured in Amana, Iowa, you can have peace of mind knowing that you are investing in a product that is made with precision and care.

Freestanding And Side-by-side Kitchenaid Refrigerators Made In Amana, Iowa

In addition to their impressive range of built-in refrigerators, KitchenAid also manufactures freestanding and side-by-side refrigerators in Amana, Iowa. These refrigerators offer versatility and convenience, making them a popular choice among homeowners.

By manufacturing freestanding and side-by-side refrigerators in Amana, Iowa, KitchenAid ensures that their appliances meet the same high-quality standards as their built-in models. With sleek designs, innovative features, and excellent performance, these refrigerators are designed to enhance your kitchen while keeping your food fresh and organized.

Whether you prefer a built-in, freestanding, or side-by-side refrigerator, choosing a KitchenAid appliance made in Amana, Iowa guarantees durability, reliability, and exceptional craftsmanship.

Kitchenaid Dishwashers Manufactured In Findlay, Ohio

All Kitchenaid Dishwashers Made In Findlay, Ohio

When it comes to KitchenAid dishwashers, you can trust that they are all manufactured in Findlay, Ohio. This bustling city in the heart of the United States is home to one of KitchenAid’s largest manufacturing facilities. By centralizing the production of their dishwashers in one location, KitchenAid ensures consistent quality and craftsmanship in every appliance.

Additional Brands Manufactured In Findlay, Ohio

Aside from KitchenAid, the Findlay facility also produces dishwashers for other renowned brands. These brands, which are synonymous with durability and innovation, include Bosch and Kenmore. Like KitchenAid, these brands place a premium on quality, and by manufacturing their dishwashers in Findlay, Ohio, they can deliver on this promise.
See Also  Mitsubishi Mini Split Not Blowing Cold Air: 10 Issues Fixed!
In conclusion, when you purchase a KitchenAid dishwasher or one from their associated brands like Bosch and Kenmore, you can be confident that it is manufactured right here in Findlay, Ohio. The skilled workforce and cutting-edge facilities in this city ensure that each dishwasher is made to the highest standards. So, go ahead and choose a KitchenAid dishwasher made in Findlay, Ohio, and experience the exceptional cleaning performance it offers.

Kitchenaid Appliances Manufactured In Other Parts Of The United States

When it comes to KitchenAid appliances, many people may wonder where they are manufactured. One of the significant manufacturing locations for KitchenAid refrigerators is found within the United States. KitchenAid takes great pride in producing a significant portion of its appliances in its home country. The company has manufacturing facilities located in several states, including South Carolina, Mississippi, Indiana, and Arkansas.

Manufacturing Of Kitchenaid Appliances In South Carolina

In South Carolina, KitchenAid manufactures a range of appliances, including refrigerators. The state is known for its skilled workforce and manufacturing expertise. KitchenAid appliances made in South Carolina benefit from the dedication and craftmanship of the workers, resulting in high-quality products that meet the brand’s standards.

Kitchenaid Appliances Produced In Mississippi

Mississippi is another state in the United States where KitchenAid appliances, such as refrigerators, are produced. The manufacturing facilities in Mississippi adhere to KitchenAid’s stringent quality control measures and ensure that each appliance meets the brand’s exacting standards. Consumers can trust that KitchenAid refrigerators made in Mississippi are built to last and provide reliable performance.

Kitchenaid Appliances Manufactured In Indiana

Indiana is home to KitchenAid’s manufacturing facilities, where a variety of appliances, including refrigerators, are produced. The state’s rich industrial history and skilled labor force contribute to the high-quality and durability of KitchenAid appliances made in Indiana. Consumers can expect innovative design, advanced features, and exceptional performance from these refrigerators.

Kitchenaid Appliances Made In Arkansas

Arkansas is yet another state where KitchenAid manufactures its appliances, including refrigerators. With state-of-the-art manufacturing facilities and a commitment to excellence, KitchenAid refrigerators made in Arkansas are known for their superior craftsmanship and reliability. Consumers can trust that their KitchenAid refrigerator, made in Arkansas, will meet their needs and expectations.

See Also  Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins

In conclusion, KitchenAid’s commitment to producing a significant portion of its appliances in the United States is evident through its manufacturing facilities in South Carolina, Mississippi, Indiana, and Arkansas. Each state brings its unique expertise and skilled workforce to ensure that KitchenAid refrigerators meet the brand’s high standards of quality and performance.

Kitchenaid Appliances Made Outside The United States

International Manufacturing Locations For Kitchenaid Products

KitchenAid, a renowned brand for high-quality appliances, manufactures its products not only in the United States but also in various international locations. This global production ensures that KitchenAid products reach customers worldwide, while maintaining their exceptional quality standards. Let’s explore some of the international manufacturing locations for KitchenAid appliances.

Kitchenaid Appliances Manufactured In China

China has emerged as one of the key manufacturing locations for KitchenAid appliances. With its state-of-the-art facilities and advanced manufacturing processes, KitchenAid ensures that its products made in China meet the same excellence standards as those manufactured in the United States. Producing appliances in China also allows KitchenAid to cater to its growing customer base in Asia.

Kitchenaid Appliances Produced In Ontario, Canada

In addition to the United States and China, KitchenAid also manufactures some of its appliances in Ontario, Canada. Known for its strong manufacturing industry, Canada provides KitchenAid with a favorable environment to produce top-notch appliances. By utilizing skilled Canadian labor and resources, KitchenAid maintains its commitment to delivering high-quality products to customers around the world.

Kitchenaid Appliances Manufactured In Quebec, Canada

Quebec, Canada, is yet another location where KitchenAid manufactures its appliances. With its robust manufacturing sector and skilled workforce, Quebec offers an ideal setting for KitchenAid to produce its renowned refrigerators and other appliances. By maintaining manufacturing facilities in Quebec, KitchenAid ensures a diverse range of production sites, allowing for efficient global distribution.

Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins


Frequently Asked Questions Of Where Are Kitchenaid Refrigerators Made

Is Kitchenaid Made In China?

KitchenAid products are manufactured in various locations including the United States and China. Some appliances are made in Ohio, South Carolina, Iowa, Mississippi, Indiana, Arkansas, Ontario, and Quebec, while others are manufactured in China. The company takes pride in producing a significant portion of its appliances in the USA.

Which Refrigerator Is Made In Usa?

Many KitchenAid refrigerators are manufactured in the United States, specifically in states like Ohio, Texas, and Tennessee.

Who Manufactures Kitchenaid Refrigerators?

KitchenAid refrigerators are manufactured in the United States. The company has manufacturing facilities in Ohio, Texas, and Tennessee.

Are Kitchenaid Refrigerators Made In Mexico?

KitchenAid refrigerators are primarily made in the United States, with manufacturing locations in states such as Ohio, Texas, and Tennessee. However, some KitchenAid refrigerators are also made in Mexico and then imported into the United States.


Kitchenaid refrigerators are proudly made in the United States. With manufacturing facilities located in various states such as Ohio, Texas, and Tennessee, Kitchenaid ensures that a significant portion of their appliances are produced in their home country. When it comes to purchasing Kitchenaid refrigerators, you can rest assured knowing that you are supporting American-made products and enjoying the high quality that Kitchenaid is known for.

Whether it’s a built-in, freestanding, or side-by-side refrigerator, Kitchenaid’s commitment to excellence is evident in every appliance they manufacture.

Continue Reading


Maytag Bravos XL Dryer Troubleshooting Guide



Maytag Bravos XL Dryer Troubleshooting

The Maytag Bravos XL is a popular large capacity dryer that is designed to tackle large loads with ease. It offers useful features like steam refresh, sanitize cycle, and advanced moisture sensing technology. However, like any household appliance, the Maytag Bravos XL dryer can sometimes malfunction or stop working properly.

When your Maytag Bravos XL dryer is not working as it should, there are several troubleshooting steps you can take before calling for professional service. This comprehensive guide will walk you through the most common Maytag Bravos XL dryer problems and provide troubleshooting tips to get your dryer back up and running optimally.

Common Problems with the Maytag Bravos XL Dryer

Some of the most frequently reported issues with the Maytag Bravos XL dryer include:

  • Dryer Won’t Start: If the dryer will not turn on at all, it could be a problem with your power supply, door latch, start button, or internal components like the motor or control board.
  • Dryer Won’t Heat: Issues like a faulty heating element, blown thermal fuse, or defective gas valve can prevent the dryer from heating properly.
  • Noisy Operation: Unusual noises when the dryer runs could indicate problems with the drive belt, drum rollers, motor, or blower.
  • Clothes Not Drying: Clogged vents, faulty moisture sensors, or thermostat issues can lead to wet clothes after a cycle completes.
  • Dryer Shuts Off Mid-Cycle: This can happen due to overloading, a faulty door switch, broken drive belt, or blocked ventilation.
  • Lint Build Up: Excess lint accumulation inside the dryer or venting can reduce airflow and drying efficiency.

By troubleshooting the specific symptoms you are experiencing, you can narrow down the root cause and determine if you can fix it yourself or need professional service.

Step-by-Step Troubleshooting for Maytag Bravos XL Dryer

When your Maytag Bravos XL dryer is not working properly, there are some logical troubleshooting steps you can take to diagnose the issue:

1. Check Power Supply and Door Switch

First, confirm that the power supply to the dryer is working correctly. Check your breaker box and make sure the dryer is getting 240V power if it’s an electric model. Also, ensure the dryer door is closing properly and activating the door switch.

See Also  Mitsubishi Mini Split Not Blowing Cold Air: 10 Issues Fixed!

2. Verify Drum Rotation

Start a timed dry cycle and listen closely to hear if the drum is turning. If it is not rotating, the drive belt could be broken or the motor faulty.

3. Test Heating Element and Thermostats

Carefully inspect the heating element for visible damage. Use a multimeter to check it and the high limit thermostat for continuity. If there is an open circuit, replace the faulty part.

4. Check Venting

Remove the lint screen and use a vent brush to clean the ductwork from the dryer to the outside vent. Lint buildup will restrict airflow.

5. Examine Moisture Sensors

The automatic moisture sensors tell the dryer when clothes are dry. If clothing remains wet, the sensors may need cleaning or replacement.

6. Inspect Drum and Rollers

A noisy dryer may have worn drum glides or rollers. Examine these components and replace any that are excessively worn. Lubricate rollers and slides with appliance oil.

7. Test Control Board

If no other defects are found, the electronic control board could be malfunctioning. Have an appliance technician test the control board for faults.

Methodically working through these troubleshooting steps will help you identify what is wrong with your Maytag Bravos XL dryer.

Read more:

Why Your Maytag Bravos Dryer Won’t Start (And How to Fix It)

Frigidaire Air Conditioner Buttons Not Working – Causes and Solutions

Frigidaire Window Air Conditioner Troubleshooting Guide

Resetting the Maytag Bravos XL Dryer

If your Maytag Bravos XL dryer is not responding to buttons presses or has frozen mid-cycle, resetting the computer may resolve the problem.

Follow these steps to reset your Maytag Bravos XL dryer:

  1. Unplug the dryer from the power source.
  2. Wait 30-60 seconds keeping the dryer unplugged.
  3. Plug the dryer back into the wall outlet.
  4. Press the Power/Cancel button on the control panel and wait a few minutes.
  5. Select a new cycle setting if desired.
  6. Press Start to begin the cycle.

This will clear any touchpad input errors and restart the dryer’s computer. Be sure to remove any clothes from the drum before resetting your Maytag Bravos XL.

If resetting the dryer does not resolve the issues, further troubleshooting of mechanical and electrical components will be required. But in many cases, a simple reset gets the dryer functioning again.

See Also  Where Are Kitchenaid Refrigerators Made: Discover the Manufacturing Origins

When to Call a Repair Professional

While many common Maytag Bravos XL dryer issues can be fixed with simple DIY troubleshooting, there are times when it is best to rely on an appliance repair technician:

  • If you have done thorough troubleshooting but the dryer still does not start or heat properly. Complex electrical issues could require an expert diagnosis.
  • For problems with the motor, gas burner assembly, or drum rollers where special tools and skills are needed for repair.
  • If the troubleshooting involves taking apart the dryer casing, which can be challenging on certain models.
  • For peculiar error codes lighting up on the dryer display that are not referenced in repair manuals.
  • When there are obvious signs of overheating, strange noises, or other potentially hazardous defects.

Trust certified Maytag appliance repair experts if your model-specific troubleshooting is unsuccessful or safety issues arise. Their technical skills and proper tools will get your Bravos XL dryer running optimally again.

DIY Maintenance Tips for Maytag Bravos XL Dryer

Taking proper care of your Maytag Bravos XL dryer can prevent many common issues and keep it operating smoothly for years. Follow these maintenance tips:

  • Clean the Lint Screen Before Every Load – Remove built-up lint from the lint screen and slot before starting a drying cycle. Lint buildup is a fire hazard.
  • Use Rigid Metal Ducting – Ensure the venting ductwork is smooth metal rather than plastic or foil. This allows maximum airflow.
  • Inspect Venting Annually – Detach the dryer venting once a year and use a vent brush to remove any accumulated lint in the system.
  • Avoid Overloading – Do not exceed the recommended load capacity for your drum size. Overloading strains the motor and prevents proper tumbling.
  • Clean the Moisture Sensors – Remove lint buildup from the metal sensor strips inside the drum periodically. Q-tips and rubbing alcohol work well.
  • Lubricate Drum Rollers and Slides – Every few years use silicone spray lubricant on the rear roller axles and plastic slide surfaces.
  • Check Drive Belt – Visually inspect the drive belt every 6 months for signs of cracking, fraying or excessive wear and replace if needed.
  • Vacuum Inside Cabinet – Use a vacuum crevice tool to remove any accumulated lint from inside the dryer cabinet, near the blower housing.
  • Level the Dryer – Confirm all four feet are solidly on the floor. Adjust as needed to prevent vibration and noise.
See Also  Maytag Bravos XL Dryer Troubleshooting Guide

Routine care and maintenance will add years of reliable performance to your Maytag Bravos XL dryer.

Parts That Commonly Need Replacement

Over time, certain parts can wear out or fail on the Maytag Bravos XL dryer. Here are some of the most commonly replaced parts:

  • Drive Belt – The drive belt connects the motor to the drum and can fray or snap from age and use. Check it if the drum won’t turn.
  • Drum Rollers – Plastic rollers at the rear of the drum that can wear down, causing noisy operation and improper tumbling.
  • Drum Slide Glides – Nylon slides under the front drum lip that allow smooth rotation. They can become damaged or worn.
  • Heating Element – If the dryer won’t heat, the internal heating element may have burned out and need replacing.
  • Thermal Fuse – This safety fuse blows if the dryer overheats due to restricted airflow or component failure. No heat is a symptom.
  • Door Switch – The small push-button switch activated when closing the door can malfunction over time, preventing starting.
  • Moisture Sensors – Metal sensor bars inside the drum that detect moisture. Defective sensors cause clothes to remain wet.
  • Gas Valve Coils – On gas dryer models, defective valve coils prevent gas flow, resulting in no heat.
  • Control Board – The electronic control board regulates all dryer functions and displays error codes if defective.

Having replacement parts on hand for these commonly failed components can reduce appliance repair costs and downtime when your Maytag Bravos XL has issues.


The Maytag Bravos XL dryer utilizes robust components and quality construction to provide dependable service. However, like any complex appliance, issues can arise over time that require troubleshooting.

Using this comprehensive guide, you can diagnose and repair many common problems with the Bravos XL dryer. Simple fixes like cleaning the lint screen, clearing vent obstructions, replacing the belt, and resetting the machine will restore normal operation in many cases.

For more complex issues involving electrical and mechanical malfunctions, rely on authorized Maytag appliance repair technicians. Their expertise can precisely identify any issue and get your large capacity Maytag dryer back up and running optimally.

With proper maintenance and care, a Maytag Bravos XL dryer should deliver years of reliable performance. Refer to these troubleshooting tips as needed to resolve problems quickly and keep your dryer spinning happily again.

Continue Reading